Application Notes

标题	产品描述
AN-2101: Mounting Recommendations for 1SP0335, 1SP0340 and 1SP0635 Gate Driver Families	Description This application note provides basic guidelines on how to install the 1SP0335, 1SP0340 and 1SP0635 gate driver families on the IGBT modules. These recommendations are helpful to ensure proper mounting of the gate driver to the target IGBT module. It should be noted that it is recommended to use the exact target IGBT module. If issues arise due to use of different IGBT package, information in this note can help.
AN-91 - BridgeSwitch PCB Configuration for 3-Phase Inverters	Description This application note compares the thermal performance of the triangular PCB configuration to the slotted linear PCB configuration with regards to case temperature rise above ambient temperature and temperature variations between adjacent BridgeSwitch devices.
AN-87 - BridgeSwitch in Single Phase BLDC Motor Drive	Description This application note describes the motor control theory and inverter drive implementation for a single-phase (BLDC) motor drive using BridgeSwitch.
AN-83 - BridgeSwitch Design Tips, Techniques and Troubleshooting Guide	Description This application note provides answers to common BridgeSwitch technical questions.
AN-80 - BridgeSwitch故障状态通信接口	Description 下载代码库：Bridgeswitch故障状态通信接口代码库
AN-79 - InSOP-24和HSOP-28波峰焊接设计指南	Description 本文件提供了InSOP-24和HSOP-28封装的波峰焊设计指南，特别是那些没有底部裸露焊盘的封装。尽管建议使用红外/对流回流焊进行表面贴装，但这两种封装在波峰焊不可用或不被首选时也可以使用。本文件提供了焊盘布局、焊盘之间的最大间距以及拖锡焊盘的方向和设计的建议。
AN-1601: Controlling SiC MOSFET Power Switches with SCALE-2 and SCALE-2+ Gate Drivers Cores and SCALE-iDriver Gate Driver ICs	Description This application note discusses procedures to optimize use SCALE gate drivers with SiC MOSFET switches.
AN-70 - LinkSwitch-TN2 设计指南	Description
AN-303 - Qspeed Family RoHS Compliant Soldering Considerations	Description Qspeed Family RoHS Compliant Soldering Considerations
AN-302 - Qspeed Reverse Voltage Sharing of Series Rectifiers	Description Reverse Voltage Sharing of Series Rectifiers
AN-301 - Qspeed Reverse Recovery Charge, Current and Time	Description Reverse Recovery Charge, Current and Time
AN-300 - Qspeed High Temperature Reverse Bias (HTRB) Reliability Testing	Description Qspeed High Temperature Reverse Bias (HTRB) Reliability Testing
AN-1301: 使用SCALE-2门极驱动器的注意事项	Description 该应用指南着重介绍在使用SCALE™-2驱动核和即插即用驱动器时必须考虑的重要事项。该指南是对应用指南AN-1101/1/的补充。
AN-0902 CONCEPT IGBT门极驱动器的防静电(ESD)要求	Description 对电子器件的任何处理都应遵循IEC 60747-1标准中所述的静电敏感器件的防护程序。CONCEPT门极驱动模块必须采取相应的方式处理。本应用指南描述处理和装配所有门极驱动器件过程中对CONCEPT产品的最低防静电要求。与MOSFET或IGBT模块相似，CONCEPT产品对静电(ESD)很敏感。
AN-1101 Application with SCALE-2 Gate Driver Cores	Description 该应用指南通过详细的示例说明了如何成功地为工业和牵引应用设计IGBT驱动器，着重介绍重要的设计规则并帮助您加快开发速度。涉及到的SCALE-2驱动核包括：2SC0108T、2SC0435T、2SC0650P和1SC2060P。
AN-1001 IGBT以及MOSFET的驱动参数的计算方法 (CN)	Description 所需的门极驱动参数的计算方法。从该应用指南中得出的数值可作为选择最适合驱动器的依据。
AN-0904 SCALE-2 门极驱动核的直接并联 (CN)	Description 传统的IGBT并联方法是由单个驱动器驱动多个IGBT，每个IGBT都有独立的门极和发射极电阻。另一种并联IGBT模块的驱动方法是，每个模块都使用独立的驱动器。
AN-0901 使用SCALE-2 IGBT驱动器控制多电平变换器拓扑的方法 (CN)	Description 该应用指南描述SCALE-2 IGBT驱动器控制多电平变换器在发生故障时的处理方法。多电平变换器使用串联IGBT，进而升高变换器输出电压的幅值和谐波频率。
AN-0801 Mechanical Handling of CONCEPT Drivers	Description 该应用指南描述装配CONCEPT驱动器的正确处理方式。需要特别指出的是，不应向变压器施加过大的机械应力。